EFFEBI-PRESS

Isolierung der Wärmeverteilungsnetze in Heizungsanlagen.

Mindeststärke des Dämmmaterials in Abhängigkeit des

Rohrdurchmessers und der thermischen Leitfähigkeit des

Dämmmaterials.

Tab. 12

Insulation of the heat distribution networks in thermal systems.

Minimum thickness of insulating material based on the diameter

of the pipe and the thermal conductivity of the insulating material.

Thermische Leitfähigkeit des

Dämmstoffs bei 40 °C

Useful thermal conductivity of the

insulating material at 40 °C

[W/m °C]

Äußerer Durchmesser des Rohrs [mm]

External diameter of the pipe [mm]

<20

20-39

40-59

0,030

13

19

26

0,032

14

21

29

0,034

15

23

31

0,036

17

25

34

0,038

18

28

37

0,040

20

30

40

0,042

22

32

43

0,044

24

35

46

0,046

26

38

50

0,048

28

41

54

0,050

30

44

58

Querschnittreduzierungen usw. Der gesamte Druckverlust in den

Rohrleitungen wird wie folgt berechnet:

Δp= Δp1 + Δp2

wobei:

Δp ist der Gesamtdruckverlust;

Δp1 ist der Druckverlust gerader Leitungen;

Δp2 ist der Druckverlust von einzeln lokalisierten Widerst

ände..

11.2 Druckverlustfestlegung - gerade Leitungen

Druckverlust mit gerade Rohrleitungen wird wie folgt berechnet

is calculated according to the following formula:

Δp= Δp1 + Δp2

where:

Δp is the total pressure drop;

Δp1 is the pressure drop due to straight lengths;

Δp2 is the pressure drop due to single localized resistances.

11.2 Pressure drops of a straight pipe

The following formula is used to calculate pressure drops, due to

straights lengths

Δp1 = ΣR • l

ΣR ist das Resultat aus R1 • I + R • I + ... + R • I

Δp1 =ΣR • l

ΣR is the result of R1 • I

1

+ R

2

• I

2

+ ... + R

n

• I

n

;

wobei:

R

ist der Druckverlustwert in bar / m oder Pa/m;

where:

R

is the unitary pressure drop expressed in mbar o in Pa/m;

1

2

2

n

n

l

ist der gerade Leitungsteil in m.

Einzeldruckverluste werden jeweils nach folgender Formel berechnet:

l

is the straight pipe length in m.

As well, the following formula is used to calculate the unitary

pressure drop:

where:

R = λ • ρ • v2/(2 • d)

λ

is the pipe friction coefficient;

ρ

is the fluid density expressed in kg/m3;

v

is the fluid speed expressed in m/s;

d

is the internal pipe diameter in mm.

For a practical calculation of pressure drops it is possible to refer

to the following tables.

wobei:

λ

ρ

v

d

R = λ • ρ • v2/(2 • d)

ist der Leitung Reibungsfaktor;

ist die Flüssigkeitsdichte des Mediums in kg/m

3

;

ist die Fließgeschwindigkeit des Mediums in m/s;

ist der Rohrleitungsinnendurchmesser in mm.

Druckverlust praktische Methode > siehe folgende Tafeln.

Manuale Tecnico [profilo V]

35

Technical Guide [V-Profile]